home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Disc Station 14
/
Disc Station Vol 14.BIN
/
drivers
/
diamond
/
stealth
/
_dmmonwi.lo_
/
_dmmonwi.lo
/
1033
/
string.txt
next >
Wrap
Text File
|
1996-05-14
|
9KB
|
212 lines
1000 Welcome to the InControl Tools 95 Monitor Wizard.
1001
1002 You have chosen to use the Monitor wizard because
1003 the manufacturer and model of your monitor is not
1004 among those listed in the Control Panel.
1005
1006 You may find the list in the Control Panel on the
1007 'Settings' page by pressing the 'Change Display Type...'
1008 button.
1009
1010
1011 If you are ready to begin click Next.
1012
1013
1040 In order to determine your monitor's capabilities we are
1041 going to apply various operating settings to your monitor.
1042 Each setting will cause your screen to flicker momentarily.
1043 When the test is done your original settings will be restored.
1044
1045 If you have never been through this process we
1046 recommend the 'Minimal' or 'Full' monitor setup,
1047 otherwise choose 'Custom'.
1048
1050 Determines which modes your monitor
1051 supports at a refresh rate of 60 Hz.
1053 Determines which modes your monitor
1054 supports at the highest refresh rate.
1056 Allows you to select your own mode
1057 and refresh rate combination.
1059 Please test this mode
1061 Mode tested and is valid
1063 Mode tested and is NOT valid
1080 You may begin testing when you are ready. The screen may
1081 flicker momentarily for each setting. The Wizard will ask
1082 you if the screen looks normal. If it doesn't look normal
1083 you can wait a moment or press the ESC key and your
1084 screen will be restored.
1085
1086
1120 You may begin testing when you are ready. The screen may
1121 flicker momentarily for each setting. The Wizard will ask
1122 you if the screen looks normal. If it doesn't look normal
1123 you can wait a moment or press the ESC key and your
1124 screen will be restored.
1125
1126
1160 You may select the modes to be tested( either one at a
1161 time or several at once). When you begin testing the
1162 Wizard will ask you if the screen looks normal. If it
1163 doesn't you can wait a moment or press the ESC key
1164 and your screen will be restored.
1165
1166
1200 The modes which your monitor can do have been collected.
1201 If you are satisfied with the test process and would like
1202 to save the results click 'Finish'.
1203
1204 If you would like to go back and perform the test again
1205 you may do so now.
1206
1207
1208
1240 There was no response to the previous mode. This probably\n
1241 means your monitor does not support this mode. Before\n
1242 continuing we wanted to protect your monitor by restoring\n
1243 it to its normal operating settings.\n\n
1244 Do you wish to continue testing?
1245
1246
1280 Does the Screen look Normal and Stable?\n\nPress 'ESC' or 'Cancel' to abort the test.\n
1281 Testing Mode:
1282 Diamond Custom Monitor Wizard - Welcome
1283 Diamond Custom Monitor Wizard - Setup Type
1284 Diamond Custom Monitor Wizard - Minimal Setup
1285 Diamond Custom Monitor Wizard - Full Setup
1286 Diamond Custom Monitor Wizard - Custom Setup
1287 Diamond Custom Monitor Wizard - Finished
1288 Minimal
1289 Full
1290 Custom
1291 Begin Testing
1292 Clear results and start over.
1293 Legend
1294 Monitor Wizard - User defined monitor not selected
1295 Diamond Custom Monitor Wizard - Owner's Manual
1296 Horizontal [ kHz ]
1297 Vertical [ Hz ]
1298 Maximum Frequencies
1299 Test Next Mode
1300 %d %% Completed
1301 Diamond Custom Monitor Wizard - Disclaimer
1302 Approximate duration of test: %d minutes
1303 Diamond Custom Monitor Wizard - Explanation
1304 The Monitor Wizard cannot test with these limits!
1340 In order to run the Custom Monitor Wizard you must first \n
1341 select '(User defined monitor types)' in the Control Panel.\n
1342 \n
1343 To make this selection do the following:\n
1344 \n
1345 1. Enter the Control Panel.\n
1346 2. Click the 'Settings' tab.\n
1347 3. Click the 'Change Display Type...' button.\n
1348 4. Click the 'Change' Monitor type button.\n
1349 5. Click the 'Show all devices' option.\n
1350 6. Click the '(User defined monitor types)' entry.\n
1351 7. Click 'OK' \n
1352 8. Click 'Close' button.\n
1353 \n
1354 You can now run the Monitor Wizard\n
1380 Please enter the frequencies listed below for your
1381 monitor. These frequencies should be found in the
1382 specification section of the manual which came with
1383 your monitor.
1384 Warning: if you enter incorrect frequencies monitor
1385 damage may result.
1400 Now select the maximum resolution for your monitor.
1401 When you are ready to continue click Next.
1440 WARNING!!! You have not entered valid values for
1441 your monitor's capabilities on the previous page!
1442
1443 If you continue this test without entering the proper
1444 values on the previous page, there is a risk that
1445 the following tests may damage your monitor! We
1446 recommend that you contact your monitor company to
1447 obtain the correct information. By clicking 'Next'
1448 you agree to hold Diamond Multimedia harmless for
1449 any and all damage which may be caused to your monitor
1450 by the following testing.
1451
1452 Without more information, the default refresh rate of
1453 60 Hz will be used throughout the test.
1454
1455 To continue at your own risk click Next.
1480 Testing stopped!
1481 Your monitor has not sync'ed with any of the 4 possible
1482 polarities for this resolution. This probably means the
1483 limit of your monitor has been exceeded and further
1484 testing could damage your monitor!
1520
1521 You have chosen the 'Full' test. This means that, within
1522 the limits specified by you on the Owner's Manual page,
1523 each of the four sync polarities will be tried at every
1524 resolution and refresh rate combination in order to
1525 locate where your monitor will sync.
1526
1527 The approximate time for the test is shown below.
1528
1529 Click Next to continue.
1560
1561 You have chosen the 'Minimal' test. This means that,
1562 within the limits specified by you on the Owner's Manual
1563 page, each of the four sync polarities will be tried at
1564 every resolution in order to locate where your monitor
1565 will sync. The refresh rate for all tests will be 60 Hz.
1566
1567 The approximate time for the test is shown below.
1569
1570 Click Next to continue.
1600
1601 You have chosen the 'Custom' test. This means that only
1602 the modes you select will be tested. You may select and
1603 test one mode at a time or you may select several modes
1604 at once. Only the modes allowed by the limits specified
1605 by you on the Owner's Manual page are listed.
1606
1607 Click Next to continue.
1640 IMPORTANT!!! In the following tests you MUST reply 'Yes'\n
1641 for each mode which makes your screen appear normal.\n\n
1642 If your screen does NOT appear normal you may press the\n
1643 ESC key, or the 'No' or 'Cancel' buttons. If you do nothing\n
1644 it is assumed your monitor did not sync!
61440 Open
61441 Save As
61442 All Files (*.*)
61443 Untitled
61696 Invalid filename.
61697 Failed to open document.
61698 Failed to save document.
61699 Save changes to %1?
61700 Failed to create empty document.
61701 The file is too large to open.
61702 Could not start print job.
61703 Failed to launch help.
61704 Internal application error.
61705 Command failed.
61706 Insufficient memory to perform operation.
61712 Please enter an integer.
61713 Please enter a number.
61714 Please enter an integer between %1 and %2.
61715 Please enter a number between %1 and %2.
61716 Please enter no more than %1 characters.
61717 Please select a button.
61718 Please enter an integer between 0 and 255.
61719 Please enter a positive integer.
61728 Unexpected file format.
61729 %1\nCannot find this file.\nPlease verify that the correct path and file name are given.
61730 Destination disk drive is full.
61731 Unable to read from %1, it is opened by someone else.
61732 Unable to write to %1, it is read-only or opened by someone else.
61733 An unexp